Hirons, beekeeper, continues his visit to the hive. Now the bees have
been smoked and quietened down, it’s time to take the top off the hive and find
out what’s going on …
little bit daunting wearing a veil over your face for the first time and
opening up a hive. Bees will land on the veil and you’ll think they are inside
and going to sting your face. Keep calm and remember you’ve worn the bee
jacket and know it well. There are no holes in it and nothing is going to
get in. Stand firm and keep calm.
the ratchet strap I have round the hive and its stand. I use it to secure
the hive against vandals, badgers and strong winds. I remove the half a
paving slab I have on the hive. I gently lift off the 4” deep tin capped
under the roof for any earwigs or spiders that may be lurking there. I see a
few earwigs so gently brush them off. I place the roof on the ground
beside the hive with the top external surface on the grass. I will put the
other hive boxes on top of the roof.
roof is removed I see the quilt or cover board. There is a hole in the
centre that fits a Porterhouse Escape. I gently put some smoke through the hole
to drive any bees that are below the cover board down into the hive. They
will move away from the smoke.
move the cover board so I gently insert my hive tool below its edge and twist
it to break the propolis seal. The cover board then starts to move and I
take it off and look underneath it. There’s a bit of comb wax on the underside
which I scrape off with my hive tool. I then put the cover board in to
the roof beside me.
down onto a box roughly 18” square with eleven frames suspended on it.
The frames have drawn out comb in half of them. Each frame is
self-spacing using a Hoffman self-spacing system that has the side of the frame
pointed on one side and flat on the other. When butted together they give me my
Bee Space. The Bee Space is 3/8” and is enough space for two bees to pass
back to back when on filled frames. Any wider and the gap would be filled by
honey comb. I talk to them and tell them I’m only having a
look. The Bees get to know your smell. They sit still and watch me. Hundreds of
little black eyes looking up and each curious as to what I want. I gently smoke
them before they decide to take flight and they slowly clear as they scurry
down the sides of the frames.
the frames, are the workers looking at me? I smoke the frame gaps a bit
more to drive most of them off the super frames I want to examine. I reach for
my hive tool and gently prise up the lugs of the empty frames. They come
away easily. There are no bees on them and I remove one frame and place
it on the cover board beside me. I now have room to move the frames a bit.
each frame, working from right to left. I move Frame Ten over to Frame
Eleven’s position and work my way to the very left. I inspect the frames
by holding them by their lugs. One lug is in my left hand and one lug in my
right. I hold the frame at an angle of 45 degrees with my left hand higher than
my right and inspect the side of the frame nearest to me and then by twisting
the frame lugs the frame revolves and I see the other side.
looking for capped honey, looking for wax moth damage and looking for hive
problems. These I will deal with later. Frames containing honey are quite
heavy, so I keep a good grip on the lugs. If there are any bees still on
the frames I’m inspecting I don’t mind; I just make sure they aren’t crushed
when I put the frame back.
capped honeycomb on the first three frames on the left, drawn comb on Four to
Seven, and Eight to Eleven are still just sheets of foundation.
all the super frames and place my hive tool under the super and break the
propolis seal to enable me to gently lift the super off. I place it on the roof
and I usually sit it crossways so it sits on the roof edges. Some bees may fall
on to the cover board below but they aren’t lost. Some may take flight but will
return to the hive.